mho

Dual 90° Ceiling Flipper

this creates 2 (4) outward facing 90° ceilings offset by 8 each (16 is needed to overlap/stack & 8 can reconnect to the original position) (its the tool i used for the Twin Repli!) just build a pillar down , snap this to it & bring 2 of these ceilings up there ( ceilings = walls , so as long as you can build cubes, you can bring both sides to the right spot) you can glue them to any ceiling if you build a 90° pillar + a beam snapped to that pillar "up there" i guarantee it will stay up on official after removing the scaffolding (there are other pieces that can glue this, but pillar+beam WORKS reliable!),the game needs to think there is a "foundation", so it needs a 90° pillar & the 90°beam on that pillar can then connect to other things (like any normal ceiling) enjoy

The Twin-Repli Crafting Oval

This places a small Foundation Oval +16 offset above a normal Floor and adds two half Circles of Dedi's [26], with the Twin-Replicators centered inside the Oval - You can snap this to any existing Foundation Grid, no matter the Height [up to ~3/4 of a wall high] As long as you have a 9x6 Hole in your Foundations & a "North-turned" snap-Point. - If its placed too low for the 90°Foundations, the 2 Failsafe Pillars will create the two 90° Ceilings! so no worries - The Foundations inside the Oval are only Suggestions [at the right height]. if you want to fill it "standalone", use the Triangles on the Outside, otherwise, just "cut" normal Ceilings trough the entire Oval's Foundations, as well as over the 90°ones. - to close this, fill the Dedi half Circles to "3-stacks", then close the Ovals walls & finish it with a rim of quarter Ceilings ontop & you have a standalone Crafting Oval! for the Dedi-Plate Version(wich goes up to 126 dedis): - make sure its placed 5 Steps High and i guarantee you, all will build Flawlessly! - if its too low, the Failsafe Pillars will kick in & build the 90° parts for you, but then you will have to pick up the Cellar-Doors, build Ceilings & Dedis in the Center & then replace the Cellar Doors, on the 90°Beams! (Dedis can not be placed after the Cellar-Doors!) enjoy

Oval Foundation Rings

Two Foundation Ovals Both are based on 24 sided triangle-circles, one using full , the other half walls enjoy

26.6° Foundation Flipper

This places four 26.6° foundations around a pillar yes this is the "quarter ramp" angle, but keep in mind that ceilings are shorter then roofs! enjoy

24 Dedi Circle

this places 24 dedi's around a 12(24small) sided triangle circle

48 Dedi Circle

this places 48 dedi's around a central pillar (on the outside of a 24(48small) sided triangle circle)

48 sided House +Floors +Roof

48Sided House with Floors & Roof - its the 48 sided small foundation circle with large walls all around - the upper rim is a layer of quarter walls, that are needed to offset the triangle roofs & also have the pillars in them to make it all "one ring" [if you want to make the foundation ring "one" , you need to add pillars on the foundations] - the entire center is just one of the four 12 sided circle plates lowered by 16 & i gave it connection to the outer rim on 3 sides with 8 offset [meaning you can freely overlap these floors & have ceilings cut into foundations] - to close the floors, fill the outer rim with triangles & then the leftover 90°gaps with quarter ceilings - lastly use quarter ceilings all around(on the large walls) to cover up your floor plates pointy ends & id recommend also adding a ring of pillar-beams! it gives it an overall solid look you can have any one wall/pillar going up to hold the floors/ceiling, i just used 3 pillars for symmetry & safety^^ - the triangle roofs would block the ramps "below them" from being build, so these have to be added by hand later on to close the roof - as final touch add a ring of railing onto the ceiling plate on top (its a great spot for a teleporter for example) - the 3 "gates" are made out of 4 tek ceiling doors, held by that pillar frame PS: the hammer is sometimes stupid & places foundations without connection to all neighbouring ones... replacing them by hand will connect to all sides.... idk why, but #arklife i think thats all enjoy

96 ,48, 24 Foundation Rings

this builds the largest possible circle the hammer allows! (if we try to pick this up anywhere else, then the central pillar, the opposite side is out of reach) a full 96 sided ~30.5 diameter circle (including the 48 and 24 sided rings) PS: i uploaded the individual circles as well!, this just has em all in one

45° Foundation Flipper

This places four 45° foundations around a central pillar (wich is the roof angle, but ceilings are shorter then roofs, keep that in mind!) enjoy

Foundation Flipper 90° +upside/down

this places four 90° Foundation around a central Pillar the foundations are turned clockwise & then flipped "nose down" if this is glued to a 90° Foundation, it will give us normal back & even upside-down! (wich means, this tool lets us freely flip back & forth, perfectly aligned!) all these angles can be interconnected & held up with pillars & beams, at any angle! enjoy

Foundation Stacker Up+Down

place this onto any foundation or pillar & it will create offsets that allow us to stack ceiling & foundations - the +/-8 offsets can connect to the starting height & the +/-16 offset can overlap ceilings! - it works any angle, even upside down! PS: this can also make dedi plates & stack fridges & co, by adding a quarter ramp to the +/-16 offset!, its all you need! this is my first template here so, enjoy